We offer Rear View Back up Camera System, Reversing Camera System, TFT LCD Monitor, Auto Shutter Camera and CCTV Camera for Car, Heavy Truck, Trailer, SUV, Farm Tractor, Forklift, Compactor Vehicle, Street Sweeper, Mobile Home, Passenger Bus and Mining Vehicle. We’ve been in this field since 1997 producing cctv cameras and car rear view camera systems. In 1999 we were the First factory producing infrared waterproof camera in China. Since then we served thousands of customers perfectly. We absolutely know we do not have the lowest price on the internet. All of the products are designed by ourselves, we choose the best materials from USA and Japan, we do not use any electrical components made in our China, because we need high quality material to ensure the stability of our products. We have professional engineers who have ten years’ experience in this field. So we can help our clients to solve any fault in use. We are top quality, we passed following tests. Load dump means the disconnection of a powered load. It can cause 2 problems. Failure of supply to equipment or customers II. Large voltage spikes from the inductive generator(s) In automotive electronics, it refers to the disconnection of the vehicle battery from the alternator while the battery is being charged. Due to such a disconnection of the battery, other loads connected to the alternator see a surge in power line. The peak voltage of this surge may be as high as 120 V and the surge may take up to 400 ms to decay. The transient high voltage which ususally occurs in automotive will damage the rear view camera system, if the system has no protection circuit. Our monitor uses a special component inside to avoid the damage. The transient high voltage will never damage our monitor. Following shows the test procedure. Connect power supply to DC input of load dump generator. Connect output of the load dump generator to component power supply lines. Set DC supply so that DC voltage to the component is 13.8VDC measured at the component. Chassis of DUT shall be physically isolated from the ground plane, and the DC supply should be electrically grounded to the ground plane. After test our monitor has no damage at all. Ri = 0.4. Electrostatic discharge (ESD) is the sudden flow of electricity between two objects caused by contact, an electrical short, or dielectric breakdown. ESD can be caused by a buildup of static electricity by tribocharging, or by electrostatic induction. ESD includes spectacular electric sparks, but also less dramatic forms which may be neither seen nor heard, yet still be large enough to cause damage to sensitive electronic devices. Electric sparks require a field strength above about 4 KV/cm in air, as notably occurs in lightning strikes. Other forms of ESD include corona discharge from sharp electrodes and brush discharge from blunt electrodes. The ESD will do harm to rear view camera system if there is no ESD protection circuit. When user operate and touch the monitor, the high electrostatic voltage of 2kv/4kv/5kv/6kv/8kv will discharge between the user and monitor, and the high voltage will damage the monitor. The high electrostatic voltage will never damage our monitor. Test methods: contact or air discharge are both acceptable. Isolate the DUT from ground-plate. We apply the discharge of 2kv/4kv/5kv/6kv/8kv to every point that the user may touch when operating our monitor. After test, our monitor still work well, no damage at all. IP69K Waterproof and Dust-proof Test. NOZZLE WATER SPRAY TEST. 9 DIGITAL WIRELESS REARVIEW BUCKUP CAMERA SYSTEM, 2.4GHZ WIRELES DIGITAL TRANSMITTER, NO INTERFERENCE. It can be used as a vision solution for any kinds of forklift trucks. The camera can be installed above the forks to surveil the loading/unloading of the forks. Drivers no more guess for it. At the same time, the monitor has a rear distance scale. When the monitor is displaying camera 1 in a full screen, drivers can estimate the distance from the forks to object by the scale. It does not need to say where the monitor should be installed. By the way, usually the power of the forklift is higher than DC 32V, so when powering the cameras and the monitor, we recommend you to use a converter to convert the forklift power into DC12V or24V or 32V, either is OK. At the same time, when powering the cameras and the monitor, the polarity of the power can not be reversed, otherwise damage caused. 9 WIRELESS LCD MONITOR1. ACCESSORIESThis kit does not have remote control. What is the difference between analog wireless camera system and the above digital wireless camera system? Both of them use the same 2.4GHz frequency technology. The 2.4GHz frequency is very common , many of our wireless device use this frequency, such as wireless router, bluetooth, etc. So the analog wireless camera system sometimes receives signal wireless routers, bluetooth and cellphone, and interferenced caused. There is no other device can transmits the same digital signal as the camera. Digital Wireless Split Monitor Camera system. No Need to Run Cables Through Farm TractorHorse Trailer, Allow You to View Your Horses and Back View. 9 Digital Split Screen TFT LCD Monitor Built-in 2.4GHz Digital Wireless Receiver, NO INTERFERENCE AT ALL. Monitor Using Techwell(made in USA) main chipset, industrial grade chipset, specially for auto electronics, more stable. CAM1 with rear view distance scale. Image Modes: single view or split view. When monitor displays in split view mode, the rear view distance scale will not be displayed on screen. DC14+87V(Td400mS) 5pulses Load Dump Test Passed300cd/m2 Brightnes. 2.4GHz Digital Wireless Camera Aluminum Camera IP69K Waterproof and 10G Vibration, IR LEDs for Night Vision. Free Operating Voltage: DC1132V. This monitor can take up to 2 cameras. Monitor can be set as split view mode or single view mode. When the monitor is in single view mode and displaying the image of camera1, there will be a rear distance scale on the screen. Digital Wireless Receive Monitor(Model:SP-966H2). 9 Digital Screen TFT LCD Monitor with Removable Sun Visor. Built in 2 CH 2.4GHz Digital Wireless Receiver. Operation Frequency:2400 2483.5MHz. Receiving Sensitivity -86dBm(1MHZ QPSK MD300RE). Overlapping Hopping Channel:80. Color System:PAL/NTSC(AUTO). Display Resolution: 800RGB(H) X 480(V) dot. Wide view angle(CR>10):(up/ down):50/70 (left/right): 70/70. Contrast ratio: 500:1. Operating temperature: -20 to +70. Storage temperature: -30 to +80. Free Operating Voltage: DC1032V. External dimensions:(L x W x T) 255.5X179X81mm. 1/3 COLOR CMOS Camera, 500tvl high resolution. Waterproof, Night Vision, Wireless Digital Transmitter Built-in. Digital Wireless Waterproof IR Camera(MODEL:DF-8275H-SFS). Image Type: 1/3 inch Color CMOS. Built in 2.4GHz Digital wireless t ransmitter. CAM1 with mirror image, CAM2 with mirror image. Horizontal Resolution:500TV Lines. Effective pixel:NTSC:NTSC:720(H)X480(V);PAL:720(H)X480(V). Usable Illumination : 0Lux (Built in 18pcs IR LED’s for Picture Support in the Dark). Free viewing angle: 115°. Free Operating Voltage: DC10-32 Volts. 106(W) x 75(H) x 70.4(D) mm (without mounting). Thanks for your business! If have questions on how to install the system, please contact me! The item “9 DIGITAL WIRELESS REAR VIEW BACKUP CAMERA SYSTEM FOR RV 5TH WHEEL TRAILER” is in sale since Monday, July 6, 2015. This item is in the category “Consumer Electronics\Vehicle Electronics & GPS\Car Video\Rear View Monitors/Cams & Kits”. The seller is “1stsafe” and is located in Guangzhou. This item can be shipped to United States, all countries in Europe, all countries in continental Asia, Canada, Australia.

• Camera Connection Type: Wireless
• Modified Item: No
• Custom Bundle: No
• Screen Display: TFT – LCD
• Country of Manufacture: China
• CAMERA: 1/3 inch Color CMOS, WATERPROOF, NIGHT VISION
• MONITOR: 9″ WIRELESS SPLIT TFT LCD MONITOR
• WIRELESS TRANSMITTING: 2.4GHZ, DIGITAL SIGNAL
• Type: Rear View Camera Kit
• MPN: DF-966H20121
• Brand: VEISE
• Non-Domestic Product: No
• Screen Size: 9″